We dry, cut out, and rebuild water-damaged walls across Keller
When a supply line lets go or a roof leak soaks your sheetrock, wall and drywall water damage repair keller TX homeowners trust starts with stopping the moisture and drying the cavity. We handle everything from moisture mapping to new drywall, texture, and paint. Serving Keller, TX and Tarrant County since 2005.
Wall and drywall water damage repair keller TX is the process of stopping the moisture source, drying the wall cavity, and replacing or refinishing drywall that has swelled, sagged, or grown mold. Water wicks upward through paper-faced drywall faster than most people expect, often climbing 12 to 18 inches in under 24 hours. We use a moisture meter and thermal imaging camera to trace exactly how far the wet zone reaches before we cut anything.
Keller homes see this constantly. Slab leaks push water up through the bottom plate, burst pipe failures soak entire walls, and roof leak water damage shows up as ceiling stains that spread down the studs. If you search for drywall water damage repair near me keller TX after a storm, you need a crew that can dry the framing first and rebuild second. We do both, and we document every step for your insurance claim.
Water-damaged drywall gets worse every hour it stays wet. Here is what you get when you call our Keller crew.
We arrive with a moisture meter, hygrometer, and infrared camera to map the wet zone in 20 to 30 minutes. That tells us exactly which studs are wet and which drywall panels can be saved, so you are not paying to replace walls that only need drying.
We cut out damaged sections to the nearest stud, then hang, tape, texture, and prime new drywall so the repair disappears. Most Keller homes have orange-peel or knockdown texture, and we match it on site. You get a wall that looks like nothing ever happened.
Mold growth can start on wet drywall paper in 24 to 48 hours. We apply an antimicrobial solution and set up containment barriers before we cut, so spores do not spread to the rest of your house. If mold is already present, we handle remediation under our Texas Mold Remediation License.
We write our scope in Xactimate, the same software most carriers use, and photograph every wet panel before removal. That means fewer back-and-forth questions and a faster claim. We have been helping Keller homeowners with water damage claims since 2005.
Every job follows the same five steps, from the first phone call to the final coat of paint. Here is what you can expect.
Call us and we dispatch a crew to your Keller address, usually within 60 to 90 minutes. We shut off the water source if it is still running, extract standing water with a water extraction unit, and set containment barriers if mold risk is high. You get a clear picture of the damage before we start cutting.
We run a moisture meter and thermal imaging camera across every wall in the affected room. Wet drywall reads 20 to 30 percent on a pin meter; dry drywall reads 8 to 12 percent. We mark the boundary with tape and photograph it for your claim. This step takes 30 to 45 minutes.
We position air movers and a dehumidifier to pull moisture out of the wall cavity and the room air. Dri-Eaz and Phoenix Restoration Equipment units run 24 hours a day, and we check readings every 24 hours with a hygrometer. Most wall cavities dry in 3 to 5 days.
Once the framing reads dry, we cut out the damaged drywall to the nearest stud, remove wet insulation, and treat the cavity with antimicrobial solution. Then we hang new drywall, tape, float, texture, and prime. A typical wall section takes 4 to 6 hours to rebuild.
We walk the room with you, check paint match under daylight and lamp light, and confirm moisture readings are back to baseline. We leave you with a written summary of what was dried, what was replaced, and what to watch for. Most Keller jobs close out in 7 to 10 days from the first call.
We have been drying and rebuilding water-damaged walls in Keller since 2005, which means we have seen how this town's slab-on-grade homes, clay soil, and summer storms interact. Our technicians hold IICRC WRT and IICRC ASD certifications, and we carry a Texas Mold Remediation License for jobs where mold has already taken hold. We use Xactimate for every insurance scope and follow IICRC S500 drying standards on every job. That combination is why local realtors and property managers keep our number.
Plenty of crews will cut out wet drywall. Fewer will dry the framing first, match your texture, and hand you a claim-ready scope. Here is what separates our Keller team.
Cutting wet drywall before the framing is dry traps moisture behind the new panel and invites mold. We take moisture meter readings at every stud bay and will not hang new drywall until the wood reads below 15 percent. That extra day of drying saves you a second repair.
Keller homes built in the 1990s and 2000s mostly have orange-peel or light knockdown texture. We carry matching compounds and blend the repair into the surrounding wall. If you have a custom finish, we test a small patch first so you can approve it before we do the whole wall.
Water does not wait for business hours. We answer calls 24/7 and can have a crew at your door within 60 to 90 minutes for emergency drywall water damage repair keller TX. The faster we extract and start drying, the more drywall we can save instead of replace.
We handle extraction, drying, drywall removal, rebuild, texture, and paint. You do not have to coordinate a separate drywall contractor after the restoration crew leaves. That single point of contact keeps your timeline tight and your claim simple.
Our standard wall and drywall water damage repair covers everything from moisture mapping through final paint. If your job needs structural framing repair or mold remediation, we handle that too and note it in the scope before we start.
We check every wall in the affected area with a moisture meter and thermal imaging camera, mark the wet boundary, and photograph it. You get a clear record of what was wet and how far the damage reached.
We remove standing water with a water extraction unit, then set air movers and a dehumidifier to dry the wall cavity. Drying typically runs 3 to 5 days with daily moisture readings to confirm progress.
We cut out damaged drywall to the nearest stud, remove wet insulation, and haul everything away. Containment barriers and a HEPA vacuum keep dust and mold spores from spreading through your Keller home.
Before we close the wall, we treat the framing and cavity with an antimicrobial solution. This stops mold growth on wet wood and drywall paper, which can start within 24 to 48 hours of a leak.
We hang new drywall, tape and float the seams, and apply texture to match the surrounding wall. Most Keller homes have orange-peel or knockdown, and we match it on site so the repair blends in.
We prime the new drywall and apply finish paint to match your existing color. If you do not have touch-up paint, we can color-match from a sample or paint the full wall for a seamless result.
Most wall water damage in Keller starts small and spreads quietly. Here are the problems we see most often and how we solve them.
Wet drywall loses strength, the paper separates, and the panel has to be replaced instead of dried. The longer it stays wet, the more square footage you pay to rebuild.
We find the leak with a moisture meter, stop it, and dry the cavity fast. If the drywall is still structurally sound, we dry it in place. If it has already crumbled, we cut it out to the nearest stud and rebuild with matching texture and paint.
Mold on drywall paper and framing releases spores into the room and can trigger allergies. It also spreads to adjacent walls if the moisture source is not fixed.
We remove mold-contaminated drywall under containment barriers, treat the framing with antimicrobial solution, and run a HEPA vacuum to clear spores. Our Texas Mold Remediation License covers the full scope, and we verify the cavity is clean before rebuild.
A roof leak or upstairs supply line soaks the ceiling and then runs down inside the wall. By the time you see the wall stain, the damage is often 3 to 4 feet wide.
We trace the leak with a thermal imaging camera, dry the ceiling and wall cavity together, and repair both surfaces. Matching texture and paint on the ceiling and wall keeps the repair invisible from below.
A burst pipe dumps gallons into the wall in minutes. The drywall bows, insulation saturates, and the studs stay wet for days without mechanical drying.
We shut off the line, extract water, and open the wall to dry the studs with air movers and a dehumidifier. Once the framing reads below 15 percent moisture, we rebuild the drywall and repaint the wall.
Wet insulation and drywall paper hold odor long after the surface feels dry. Painting over it traps the smell and the moisture, and the odor returns within weeks.
We remove the wet materials, treat the cavity with antimicrobial solution, and run HEPA filtration and dehumidification until readings return to normal. Then we rebuild the wall so the odor does not come back.
We extract water on both floors, open the wall to dry the studs, and check the ceiling below with a moisture meter. After 3 to 5 days of drying, we rebuild the drywall on both levels and repaint.
Two walls and one ceiling repaired with matching texture, and no mold growth in the cavity.
We locate the leak with a moisture meter and thermal camera, coordinate the plumbing repair, then dry the wall cavity and replace the bottom 12 to 18 inches of drywall and the baseboard.
The wall is dry, the baseboard is replaced, and the paint blends into the hallway.
We tarp the roof, extract water from the wall cavity, and dry the framing with air movers and a dehumidifier. Then we cut out the damaged drywall, rebuild it, and match the texture.
The window wall is repaired and painted, and the roof leak is documented for your insurance claim.
We remove the water heater, extract standing water, and open the wall to dry both sides. After drying, we replace the insulation and drywall and repaint the living room wall.
The shared wall is dry and rebuilt, and the living room looks untouched.
We use a pin-type moisture meter to read moisture content in drywall and framing, and a hygrometer to track relative humidity in the room. Readings tell us when the wall is dry enough to rebuild.
An infrared camera shows temperature differences behind the wall, which reveals wet spots you cannot see. We use it to map the full wet zone before we cut anything.
A boroscope lets us look inside the wall cavity through a small hole. We use it to check for mold growth and to confirm the framing is dry before closing the wall.
High-velocity air movers from Dri-Eaz and Phoenix Restoration Equipment push air across the wall surface and into the cavity. We position them to dry the studs and the back of the drywall at the same time.
A refrigerant or desiccant dehumidifier pulls moisture out of the air so wet materials can release water vapor. We run it 24 hours a day and check the condensate output to confirm it is working.
When mold is present, we set plastic sheeting and containment barriers to isolate the work area. A HEPA vacuum captures spores during removal so they do not spread to the rest of your home.
A portable extraction unit pulls standing water out of carpet, subflooring, and wall bases. Removing water fast limits how high the drywall damage climbs.
We follow the IICRC S500 standard for water damage restoration, which sets target moisture levels, drying timelines, and documentation requirements. That is why we take daily readings and photograph the wet zone before and after drying.
We write every insurance scope in Xactimate, the estimating software most carriers use. Line items match industry pricing, which reduces back-and-forth with your adjuster and speeds up approval.
After removal and before rebuild, we apply an antimicrobial solution to the framing and cavity. Products like Benefect and Decon 30 are plant-based and safe for occupied homes, and they stop mold growth on wet wood.
We test texture on a small patch before applying it to the whole repair. Orange-peel, knockdown, and custom finishes all require different compounds and spray settings, and matching on site keeps the repair invisible.
Keller sits on expansive clay soil that shifts with wet and dry cycles, and that movement is hard on the plumbing under slab-on-grade homes. When a slab leak develops, water pushes up through the bottom plate and wicks into the drywall from below, which is why we always check the bottom 24 inches of a wall first. Summer storms roll through Tarrant County from May through September and drive rain through roof vents and window frames, soaking drywall from the top down. Winter freezes burst pipes in attics and exterior walls, and we see a spike in emergency drywall water damage repair keller TX calls when temperatures drop below 20 degrees. Most Keller homes were built between 1985 and 2015 with orange-peel or light knockdown texture, and we carry matching compounds on every truck. If you need to fix water damaged drywall keller TX after any of these events, we can usually be at your door in 60 to 90 minutes.
Many homes here have two-story foyers and upstairs laundry rooms, which is where we see the most supply line failures that soak the wall below.
Older homes in this area have copper supply lines that are more prone to pinhole leaks, which slowly soak the drywall behind cabinets and baseboards.
Slab-on-grade construction and mature trees mean root intrusion into sewer lines, which can back up and soak the lower drywall in hallways and bathrooms.
Roofs here take a beating from summer hail, and we see ceiling and wall damage from roof leaks after most major storms.
Shifting soil cracks supply lines and drain pipes under the slab. Water then wicks up into the bottom of the drywall, which is why we always check the base of the wall first.
Storms from May through September drive rain through roof vents and damaged shingles. The water runs down inside the wall and soaks the drywall from the top down.
When temperatures drop below 20 degrees, pipes in attics and exterior walls can freeze and burst. A burst pipe soaks drywall and insulation in minutes, so we treat these as emergency calls.
Humidity above 60 percent slows drying and can keep a wall cavity wet longer than expected. We run dehumidifiers continuously and check readings daily to confirm the wall is drying.
A supply line behind the kitchen sink let go overnight and soaked the wall 18 inches up from the floor. The drywall was soft, the insulation was saturated, and the baseboard had started to cup. The homeowner found standing water on the tile the next morning.
We extracted the water, opened the wall, and dried the studs for four days. Then we replaced the insulation, hung new drywall, matched the orange-peel texture, and repainted the wall. Total job time was eight days, and the repair is invisible.
Check the supply line fittings under the sink once a year and replace the flexible line every five years. A $15 line is cheaper than a wall rebuild.
A slab leak pushed water up through the bottom plate of a hallway wall in a Keller home. The bottom 12 inches of drywall read 28 percent on a moisture meter, and the paint was starting to bubble. The homeowner noticed the baseboard was loose.
We located the leak with a thermal camera, coordinated the plumbing repair, and dried the wall cavity for five days. Then we replaced the bottom 14 inches of drywall and the baseboard and repainted the hallway. The wall now reads 10 percent moisture.
Watch for loose baseboards or bubbling paint along the bottom of walls. Both are early signs of a slab leak before the drywall softens.
A summer storm drove rain through a roof vent and soaked the drywall around an upstairs window in a Woodland Springs home. The ceiling below showed a brown stain, and the wall read 24 percent moisture from the window down to the floor.
We tarped the roof, extracted water from the wall cavity, and dried the framing for four days. Then we cut out the damaged drywall, rebuilt the window wall, and matched the texture and paint. The ceiling was repaired in the same visit.
Have your roof inspected after every major hail storm. A cracked vent boot is a $50 fix that prevents a $2,000 wall repair.
Most Keller drywall water damage repairs run $450 to $2,800, depending on how many square feet are wet and whether the framing needs drying. A single wall section with minor damage often lands near the low end. Whole-room rebuilds with texture and paint push toward the high end. We provide a written scope before work begins.
We stop the water source, extract standing water, and dry the wall cavity with air movers and a dehumidifier for 3 to 5 days. Once the framing reads dry on a moisture meter, we cut out the damaged drywall, treat the cavity, and hang new panels. Then we tape, texture, prime, and paint to match.
Most homeowners policies in Keller cover sudden and accidental water damage, like a burst pipe or appliance leak, including drywall removal and rebuild. Gradual leaks and long-term neglect are usually excluded. We document every wet panel with photos and moisture readings to support your claim.
Expect 7 to 10 days from the first call to final paint on a typical Keller wall repair. Drying takes 3 to 5 days, drywall removal and rebuild take 1 to 2 days, and texture and paint add another 1 to 2 days. Larger jobs with multiple rooms can run 2 to 3 weeks.
They came out on a Saturday after our water heater leaked into the wall. Moisture mapping took about 30 minutes and they showed us exactly where the water had traveled. Drying took four days, then they rebuilt the drywall and painted. You cannot see the repair.
We had a slab leak that soaked the bottom of our hallway wall. They coordinated with our plumber, dried the cavity, and replaced the drywall and baseboard. The texture match is perfect and they cleaned up every day before leaving.
A pipe burst in our attic during a freeze and water ran down two walls. They were at our house in about an hour, extracted the water, and set up drying equipment. Eight days later the walls were rebuilt and painted. Insurance covered it with their scope.
I manage rentals in Keller and Roanoke and have used them three times. They document everything for the claim, they show up when they say they will, and the drywall work is clean. The last job had two wet walls and they finished in eight days.
Before we can repair drywall, standing water has to go. We pull water out of carpet, subflooring, and wall cavities with a water extraction unit, usually within 60 to 90 minutes of your call in Keller.
Emergency Water ExtractionWet framing behind drywall has to dry before we rebuild. We set air movers and dehumidifiers for 3 to 5 days and monitor with a hygrometer until studs read below 15 percent moisture content.
Structural Drying & DehumidificationIf mold has already colonized your drywall paper, we remove it under containment barriers with a HEPA vacuum and antimicrobial solution. Our Texas Mold Remediation License covers the full scope in Keller.
Mold RemediationSewage backup soaks drywall with contaminated water that requires removal, not drying. We cut out affected panels, disinfect the cavity with Benefect or Decon 30, and rebuild once the framing is clean.
Sewage Backup CleanupWall and drywall repair is one piece of a full water damage restoration. We handle extraction, drying, content cleaning, and rebuild so your Keller home goes back to normal in one coordinated job.
Water Damage RestorationWhen water damage goes beyond drywall into baseboards, trim, or subflooring, our reconstruction crew rebuilds those elements to match. We keep the same crew on the job from demolition through final paint.
Water Damage ReconstructionFlood water from storms or creek overflow soaks drywall fast and often carries contaminants. We extract, cut out affected panels, dry the framing, and rebuild walls across Keller and Tarrant County.
Flood Damage RestorationKeller homes with basements or below-grade rooms see water wick up the lower drywall after a flood. We extract, cut the wet zone, dry the cavity, and rebuild the wall to a clean finish.
Basement Flood CleanupCleanup covers the whole affected room, not just the wall. We remove wet materials, dry the space, clean surfaces, and prep the area so drywall repair can start on a dry, clean substrate.
Water Damage CleanupStanding water against a wall keeps wicking upward. Our water extraction unit pulls water out of carpet and subflooring fast, which limits how high the drywall damage climbs in your Keller home.
Water ExtractionIf water is still pooled in a room, drywall damage gets worse every hour. We remove standing water with pumps and extraction units, then start drying the wall cavity the same day.
Standing Water RemovalCeiling water damage and wall damage often happen together after a roof leak. We repair both surfaces, matching texture and paint so the ceiling and wall blend seamlessly in your Keller home.
Ceiling Water Damage RepairWet carpet holds water against the bottom of your drywall, which is where wicking starts. We extract the carpet, dry the pad, and check the wall base with a moisture meter before we decide what drywall to replace.
Carpet Water ExtractionHardwood floor water damage and drywall damage usually come from the same leak. We dry and restore the floor while repairing the wall, so both surfaces are handled by one crew in Keller.
Hardwood Floor Water Damage RestorationWet drywall and insulation produce a musty odor that lingers after the wall looks dry. We treat the cavity with antimicrobial solution and run HEPA filtration to clear the smell before rebuild.
Water Damage Odor RemovalNorth Texas storms drive rain through roofs and windows, soaking drywall from the top down. We tarp, extract, dry, and rebuild walls after storm water damage in Keller and nearby cities.
Storm Water Damage RestorationA burst pipe inside a wall soaks drywall and insulation in minutes. We shut off the line, extract water, open the wall, dry the cavity, and rebuild the drywall once the framing is dry.
Burst Pipe Water Damage RepairAppliance leaks from washing machines and water heaters soak the wall behind them. We pull the appliance, extract water, dry the wall cavity, and repair the drywall before you reinstall anything.
Appliance Leak CleanupRoof leak water damage shows up as ceiling stains and wall damage below. We trace the leak with a moisture meter, dry the framing, and repair the drywall and ceiling in one visit.
Roof Leak Water Damage RepairBefore we cut drywall, we map the wet zone with a thermal imaging camera and moisture meter. That tells us exactly where the leak is and how far the damage reaches in your Keller home.
Moisture Mapping & Leak DetectionIf you smell mold but cannot see it, we inspect the wall cavity with a boroscope and take air samples. Testing tells us whether the drywall needs removal or just drying and treatment.
Mold Inspection & TestingFurniture and belongings pushed against wet walls often absorb moisture. We clean and dry salvageable items while we repair the drywall, so your room comes back together in one job.
Water Damage Content RestorationKeller businesses with wet drywall need fast turnaround to stay open. We work after hours, dry the walls, and rebuild with commercial-grade materials to get you back to normal quickly.
Commercial Water Damage RestorationWe photograph every wet panel, log moisture readings, and write the drywall scope in Xactimate. That documentation gives your Keller insurance adjuster exactly what they need to approve the claim.
Insurance Claim AssistanceWater damage to drywall gets worse by the hour. We answer calls around the clock and can have a crew at your Keller door within 60 to 90 minutes to stop the water and start drying.
24/7 Emergency Water Damage ResponseCrawl space flooding pushes moisture up into the walls above. We remove water from the crawl space, dry the joists, and check the drywall above for wicking before we repair it.
Crawl Space Water RemovalDehumidifiers pull moisture out of the air so wet drywall and framing can dry. We size the units to the room and run them 24 hours a day until readings return to normal.
Dehumidification ServicesWhen water damages studs, plates, or subflooring behind the drywall, we repair the structure before we hang new panels. That keeps your Keller home safe and your rebuild durable.
Structural Water Damage RepairDrying is the step that decides whether drywall can be saved. We use air movers, dehumidifiers, and daily moisture readings to dry the wall cavity in 3 to 5 days whenever possible.
Water Damage DryingReal experiences from customers who chose our Wall & Drywall Water Damage Repair services
A supply line behind our kitchen wall let go on a Sunday night. The crew was at our door in about an hour, shut the water off, and had air movers running before midnight. They cut out the wet drywall on Tuesday, rebuilt it Thursday, and matched our orange-peel texture perfectly. You cannot tell where the repair was.
Homeowner, Keller
We had a roof leak that soaked the wall below our upstairs window. They used a thermal camera to find exactly how far the water had traveled, which saved us from replacing the whole wall. Drying took four days, then they rebuilt the section and painted it. Insurance covered it with their Xactimate scope.
Homeowner, Southlake
I manage several rentals and have used this crew three times for burst pipe water damage repair. They are consistent, they document everything for the claim, and they do not leave a mess. The last job in Keller had two walls wet and they had it dried, rebuilt, and painted in eight days.
Property Manager, Roanoke
A supply line behind our kitchen wall let go on a Sunday night. The crew was at our door in about an hour, shut the water off, and had air movers running before midnight. They cut out the wet drywall on Tuesday, rebuilt it Thursday, and matched our orange-peel texture perfectly. You cannot tell where the repair was.
Homeowner, Keller
We had a roof leak that soaked the wall below our upstairs window. They used a thermal camera to find exactly how far the water had traveled, which saved us from replacing the whole wall. Drying took four days, then they rebuilt the section and painted it. Insurance covered it with their Xactimate scope.
Homeowner, Southlake
Every hour wet drywall stays wet, the repair gets bigger. Call our Keller crew for a free assessment and a written scope. We are IICRC certified, licensed for mold remediation in Texas, and have served this area since 2005.