IICRC-certified drying crews serving Keller and Tarrant County since 2005
When water damage drying keller TX homeowners can count on, our IICRC-certified team arrives fast with truck-mounted extraction and industrial dehumidifiers. We dry flooded carpets, soaked drywall, and wet subfloors before mold takes hold. Serving Keller, TX and surrounding Tarrant County neighborhoods, we handle burst pipes, slab leaks, and appliance failures 24/7. One call gets water out and dry air in.
Water damage drying keller TX is the controlled process of removing standing water and then pulling trapped moisture out of building materials until they return to safe, pre-loss moisture levels. It is not a fan pointed at a wet floor. We use moisture meters, thermal imaging cameras, and hygrometers to map exactly where water traveled behind baseboards, under hardwood, and inside wall cavities. Then we place air movers and dehumidifiers to dry the structure in a measured, documented way. Drying is the step that decides whether your home smells clean in a week or grows mold in a month.
Keller sits in Tarrant County where clay soil shifts with every wet-dry cycle, and that movement stresses supply lines and slab plumbing. Add summer storms that dump two inches in an hour, and winter freeze events that split copper pipe, and you get a steady stream of emergency water damage drying keller calls. Most of the jobs we run here start with a burst pipe, a slab leak, or an appliance supply line that let go while nobody was home. Water sits, drywall wicks, and mold can begin colonizing within 24 to 48 hours.
Drying is the difference between replacing a section of baseboard and replacing a whole floor. Here is what professional drying services keller homeowners hire us for actually deliver.
Mold growth begins within 24 to 48 hours of a leak, and Keller's humid summers push that clock faster. We extract standing water, apply an antimicrobial solution, and start airflow the same day. That narrow window is why we answer calls at 2 a.m. and not just during business hours.
Hardwood floor water damage is reversible if drying starts within about 72 hours. We use desiccant dehumidifiers and controlled air movement to pull moisture from plank edges and subflooring before cupping becomes permanent. Homeowners avoid a full tear-out and keep the floor they paid for.
We photograph moisture readings, log daily drying data, and build Xactimate-compatible reports your adjuster can read. That paperwork is often the difference between a covered claim and a denied one. You get a clear record of what was wet, what we did, and what it cost.
Standing water and wet drywall release odors and airborne particles. We run HEPA vacuum filtration and containment barriers when needed, then verify with a hygrometer that materials are back to normal. You walk back into a dry, neutral-smelling house, not a damp one.
Every job follows the same five stages, from the first phone call to the final moisture reading. You will know what is happening at each step and how long it takes.
You call, we ask a few questions about the source and the rooms affected, and a crew rolls out. In Keller and the surrounding Tarrant County area, we typically arrive within 60 to 90 minutes. We bring extraction equipment, air movers, and dehumidifiers on the first trip so drying starts immediately.
We walk the space with a moisture meter, thermal imaging camera, and infrared camera to find water you cannot see. A boroscope checks inside wall cavities. We mark wet zones on a floor plan and photograph everything for your insurance file. This usually takes 30 to 45 minutes.
Truck-mounted water extraction units pull standing water from carpet, padding, and hard floors. For deeper water, we use submersible pumps first. Extraction is usually finished within one to three hours depending on how much water is present. We remove saturated carpet padding because it will not dry in place.
We set Dri-Eaz and Phoenix Restoration Equipment air movers and dehumidifiers to dry walls, subflooring, and framing. Desiccant dehumidifiers handle humid Texas air. We check readings daily with a hygrometer and adjust equipment placement. Most residential jobs dry in three to five days.
We compare final moisture readings to a dry standard from an unaffected part of your home. When materials are within range, we remove equipment and give you a written drying report. If reconstruction is needed, we hand you a clear scope and can schedule the repair work.
Pro Water Damage Restoration has been drying homes and businesses since 2005, which means 21 years of Texas floods, freeze events, and slab leaks. Our technicians hold IICRC WRT and IICRC ASD certifications, and we maintain Texas Mold Remediation License credentials along with OSHA 10 and EPA Lead-Safe Certification. We have dried everything from a single bathroom to a 40,000-square-foot commercial building. That experience shows up in how fast we find hidden moisture and how accurately we document it for your insurance company.
Plenty of companies own a dehumidifier. Fewer understand how Texas heat, clay soil, and older Keller plumbing interact to create hidden moisture problems. Here is what sets our drying work apart.
We run 24/7 water damage drying keller calls year-round, including holidays. Our trucks are staged across Tarrant County so we are not driving from across the metroplex. That response time is why we can start extraction before water has time to soak into subflooring.
Every job includes moisture maps, daily drying logs, and photo documentation formatted for Xactimate. Adjusters approve claims faster when the file is complete. We also work directly with your insurance company so you are not stuck relaying messages between contractor and carrier.
We use Dri-Eaz and Phoenix Restoration Equipment air movers and dehumidifiers, not box-store fans. A single desiccant dehumidifier can pull 100-plus pints of water per day from the air. That capacity is what turns a five-day dry into a three-day dry on larger jobs.
Drying is one step. If a burst pipe caused the damage, we can coordinate the repair. If mold is already present, our Texas Mold Remediation License lets us treat it. If drywall or baseboards need replacing, we handle water damage reconstruction too. One company, one point of contact.
Every drying job starts with a full inspection and ends with verified dry readings. Here is what is included in a standard residential drying scope, and what we handle as an add-on when the damage goes further.
We use moisture meters, thermal imaging cameras, and infrared cameras to find every wet zone, including behind walls and under floors. A boroscope checks inside cavities. You get a marked floor plan and photos for your records.
Truck-mounted extraction units and submersible pumps remove standing water from carpet, padding, and hard surfaces. We remove saturated carpet padding because it will not dry in place and traps moisture against the subfloor.
We position Dri-Eaz and Phoenix Restoration Equipment air movers and dehumidifiers to dry walls, framing, and subflooring. Desiccant units handle humid Texas air. Equipment placement is adjusted daily based on moisture readings.
We apply an antimicrobial solution to wet framing, drywall edges, and subflooring to slow mold growth while drying is underway. For contaminated water like sewage backups, we use Benefect and Decon 30 disinfectants before drying.
A technician checks moisture readings every day with a hygrometer and logs them. We photograph equipment placement and material conditions. That daily log becomes the drying report your insurance adjuster uses to approve the claim.
We compare final readings to a dry standard taken from an unaffected area of your home. When materials are within range, we remove equipment and provide a written drying report. If repairs are needed, we give you a clear scope.
Most Keller drying calls start with one of a handful of problems. Each one has a different timeline and a different risk if it is ignored. Here is how we handle the ones we see most.
Water inside a wall wicks upward and sideways, soaking insulation and drywall far beyond the visible leak. Mold can start within 48 hours, and the wall often looks dry on the surface.
We shut off the water, cut a small access opening if needed, and dry the cavity with directed air movers. A boroscope confirms the cavity is dry before we close it. We also coordinate the pipe repair so the leak is fixed, not just dried.
Slab leaks in Keller's clay soil can run for weeks before you notice a warm spot or a rising water bill. By then, carpet, pad, and baseboards are saturated and the subfloor is at risk.
We use thermal imaging and moisture meters to map the spread, extract water from carpet and pad, and dry the slab and framing with dehumidifiers. We document everything for your insurance claim and can coordinate leak detection.
Dishwasher and refrigerator leaks often go unnoticed because the water runs under cabinets and into the subfloor. By the time you see warped flooring, the damage is already hidden and spreading.
We pull the appliance, extract standing water, and dry the cabinet base and subfloor with directed airflow. An antimicrobial solution goes down before drying starts. We check adjacent rooms because water follows the path of least resistance.
A ceiling stain is the visible part. Water travels along joists and can soak insulation and attic framing, creating a mold risk far from the stain. Ignoring it usually means a larger repair later.
We trace the leak path with infrared cameras, dry the ceiling structure and attic framing, and treat with antimicrobial solution. Once dry, we repair the drywall and repaint. Roof repair itself is coordinated with a roofing partner.
Sewage is contaminated water and cannot be dried like a clean-water loss. Without proper disinfection, bacteria and mold remain in the structure even after it looks dry.
We remove affected materials, apply Benefect and Decon 30 disinfectants, then dry the structure with commercial equipment. Our Texas Mold Remediation License covers any remediation that follows. We document the category of water for your claim.
We extract standing water from the floor, open the ceiling where needed, and dry both levels at once with air movers and dehumidifiers. Thermal cameras confirm the ceiling cavity is dry before we close it.
Ceiling and floor dry in four to five days, with drywall repair scheduled as a follow-up. No mold, no lingering smell.
We arrive within 90 minutes, shut off the supply, extract the water, and set drying equipment. The concrete and drywall are dried together, and we check behind the baseboards with a moisture meter.
Garage and hallway dry in three days. Baseboards are saved, and the insurance report is ready for your adjuster.
We trace the moisture with infrared cameras, dry the ceiling and attic framing, and apply antimicrobial solution. Once readings are normal, we repair the drywall and repaint to match.
Ceiling is dry in three to four days and repaired within a week. No stain, no mold.
We map the moisture footprint, extract from carpet and pad, remove saturated padding, and dry the slab and framing. Antimicrobial solution goes down before drying. We coordinate leak detection and repair.
Rooms dry in five days with no odor. Carpet is replaced, and the subfloor is verified dry before new pad goes down.
We extract the water, set up commercial-grade dehumidifiers and air movers, and dry the walls and floor. We work around your operating hours to minimize downtime.
Kitchen is dry in two to three days and back in service. Documentation is ready for your commercial claim.
Measures moisture content in drywall, wood, and subflooring so we know exactly where water traveled and when materials are dry.
Reveals temperature differences that indicate hidden moisture behind walls, under floors, and above ceilings without cutting into the structure.
Confirms wet zones found during inspection and helps us track drying progress in areas we cannot see directly.
Dri-Eaz and Phoenix Restoration Equipment air movers circulate high-volume air across wet surfaces to speed evaporation.
Removes moisture from the air so wet materials can continue releasing water. We use both desiccant and refrigerant units depending on conditions.
Truck-mounted units pull hundreds of gallons from carpet, padding, and hard floors far faster than portable shop vacuums.
Measures relative humidity and dew point so we can verify that the drying environment is actually pulling moisture out of materials.
We follow the IICRC S500 standard for water damage restoration, which defines drying goals, equipment ratios, and documentation requirements. It is the benchmark insurance adjusters recognize.
We map wet zones with moisture meters and thermal imaging before placing equipment. Mapping prevents the common mistake of drying the visible area while missing water behind a wall or under a cabinet.
Every day we record moisture readings, temperature, and relative humidity at each monitoring point. Those logs show drying progress and become the evidence your insurance company uses to approve the claim.
When mold risk is high or remediation is underway, we set containment barriers with plastic sheeting and duct tape and run HEPA vacuum filtration. This keeps spores from spreading to clean areas of your home.
We apply antimicrobial solution to wet framing, drywall edges, and subflooring before and during drying. For contaminated water, we use Benefect and Decon 30 disinfectants. This slows microbial growth while the structure dries.
A mix of older slab-foundation homes and newer townhomes. Slab leaks and supply line failures are the most common calls we get here.
Larger homes with multiple bathrooms and long supply runs. A single upstairs leak can travel far before it shows on a ceiling below.
Family homes with finished basements and bonus rooms. Sump failures and foundation seepage are recurring issues after heavy spring rain.
Newer construction with engineered flooring and tight wall assemblies. Drying requires careful humidity control to avoid cupping.
Established neighborhood with mature trees whose roots can stress sewer lines, leading to backups that need contaminated-water drying.
Shifts stress underground plumbing and can cause slab leaks that run for weeks before you notice. We map the moisture footprint carefully because the source is often far from the visible damage.
Roof leaks and window seepage soak insulation and drywall fast. We see a spike in ceiling water damage calls from May through September and keep crews ready.
Copper supply lines in attics and garages split when temperatures drop below freezing. These calls often involve multiple leaks in one home, so we bring extra equipment on the first trip.
Keller's humid air slows evaporation, so drying takes longer without proper dehumidification. We size desiccant dehumidifiers to the job rather than relying on air movers alone.
A supply line under the kitchen sink let go overnight and flooded the cabinet base, tile floor, and part of the adjacent hallway. Water had been sitting for about eight hours when the homeowner called.
We extracted 40 gallons, removed saturated cabinet base material, and dried the floor and walls in four days. Moisture readings returned to the dry standard, and no mold developed. The homeowner avoided replacing the entire floor.
Check supply lines under sinks every six months and replace braided lines every five years. A $15 line is cheaper than a $3,000 drying job.
A slab leak soaked the carpet and pad in two bedrooms and started wicking into the baseboards. The homeowner noticed a musty smell and a higher water bill but could not find the source.
We mapped the moisture with thermal imaging, extracted from carpet and pad, removed saturated padding, and dried the slab and framing in five days. The musty odor was gone, and the subfloor tested dry before new carpet went down.
Watch your water bill for unexplained increases and check for warm spots on the floor. Early slab leak detection saves thousands in drying and repair.
A flashing failure let rain into an upstairs bedroom ceiling during a June storm. The stain was small, but infrared imaging showed water had traveled along two joists and soaked the insulation above.
We dried the ceiling structure and attic framing in three days, applied antimicrobial solution, and repaired the drywall. The ceiling was repainted to match, and the homeowner avoided a mold problem in the attic.
Inspect roof flashing each spring before storm season and check attic insulation after any heavy rain for damp spots.
Most residential drying jobs in Keller run $1,200 to $3,500 for a single affected room, and $4,000 to $8,000 for multiple rooms or a full floor. The price depends on how much water was extracted, how many air movers and dehumidifiers are needed, and how many days drying takes. We provide a written estimate before work begins and bill insurance directly when the loss is covered.
Most Keller homes dry in three to five days. A small bathroom with a supply line leak may finish in two to three days. A slab leak that soaked multiple rooms can take five to seven days. We check moisture readings daily and remove equipment as soon as materials hit the dry standard, so you are not paying for extra days.
Yes. We provide professional drying services keller homeowners and businesses rely on, including emergency water damage drying keller TX calls 24 hours a day. Our IICRC-certified crews handle extraction, structural drying, dehumidification, and moisture verification. We serve Keller, Southlake, Roanoke, Trophy Club, and the surrounding Tarrant County area.
We use truck-mounted water extraction units, Dri-Eaz and Phoenix Restoration Equipment air movers, desiccant and refrigerant dehumidifiers, moisture meters, thermal imaging cameras, infrared cameras, and hygrometers. For hidden moisture we use a boroscope inside wall cavities. When mold risk is high, we add HEPA vacuum filtration and containment barriers. Every reading is logged daily for your insurance file.
Fast response when our pipe burst in January. The crew was at our Keller house in about an hour, extracted the water, and set up drying equipment. They checked readings every day and explained everything. Four days later, dry. The insurance report was complete and our claim went through without a fight.
We had a slab leak in Southlake that soaked two bedrooms. Pro Water Damage Restoration used a thermal camera to find the full extent, dried everything in five days, and coordinated the repair. No mold, no smell. They know what they are doing.
As a property manager in Roanoke, I have used them three times. Their daily moisture logs make insurance claims easy, and they always answer the phone. Drying is done right the first time, which is why I keep calling them.
Extraction is the first step of drying and the one that matters most. We pull standing water from carpet, padding, and hard floors with truck-mounted units before setting drying equipment. In Keller, we typically arrive within 60 to 90 minutes of your call.
Emergency Water ExtractionThis is the core of what we do. Air movers and dehumidifiers dry wall cavities, subflooring, and framing over three to five days. We monitor with hygrometers daily and adjust equipment placement until every material reads at the dry standard.
Structural Drying & DehumidificationIf mold has already started, drying alone will not fix it. Our Texas Mold Remediation License lets us treat affected areas with antimicrobial solution, remove contaminated materials, and verify clearance. We often combine remediation with drying on the same job.
Mold RemediationSewage backups are a contaminated water category and require more than drying. We remove affected materials, apply Benefect and Decon 30 disinfectants, then dry the structure. Keller homes on older sewer lines call us for this more often than you would expect.
Sewage Backup CleanupDrying is one phase of a larger restoration. When your loss needs repairs after drying, we handle the full scope, from drywall and paint to flooring. You get one contractor from emergency call to finished room.
Water Damage RestorationAfter drying, some materials cannot be saved. We rebuild drywall, baseboards, subflooring, and paint to match your existing finishes. Keller homeowners get a finished room, not a dried-out shell.
Water Damage ReconstructionStorm flooding brings mud, debris, and contaminated water. We extract, clean, and dry, then handle repairs. Keller's summer storms can drop two inches in an hour, and we run these calls around the clock during storm season.
Flood Damage RestorationKeller homes with basements or below-grade rooms flood from sump failures and foundation seepage. We pump standing water, extract from carpet and concrete, and dry with commercial dehumidifiers. We also check for hidden moisture behind finished walls.
Basement Flood CleanupCleanup covers the removal of damaged materials, debris, and contaminated items before drying begins. We haul out saturated carpet padding, ruined insulation, and unsalvageable drywall so air can reach the structure.
Water Damage CleanupTruck-mounted extraction removes hundreds of gallons quickly. We use submersible pumps for deep water and extraction wands for carpet and pad. This step cuts drying time significantly because less water means less work for the dehumidifiers.
Water ExtractionStanding water keeps spreading into walls and under floors every hour it sits. We pump and extract it, then map the moisture footprint with thermal imaging. Getting it out fast is the single biggest factor in whether mold becomes a problem.
Standing Water RemovalCeiling water damage from roof leaks or upstairs plumbing often hides above the visible stain. We use infrared cameras to find the wet zone, dry it, then repair drywall and repaint. Ignoring a ceiling stain usually means a bigger repair later.
Ceiling Water Damage RepairDrywall wicks water upward and sideways, so the wet area is always bigger than the stain. We measure with moisture meters, dry the cavity, and replace only what cannot be saved. Baseboards and insulation are checked at the same time.
Wall & Drywall Water Damage RepairCarpet can often be saved if extraction starts within 24 hours. We pull water from carpet and pad, then dry with air movers. Saturated padding is removed because it traps moisture and will not dry in place.
Carpet Water ExtractionHardwood floor water damage is time-sensitive. Cupping and buckling become permanent after about 72 hours. We use controlled drying with desiccant dehumidifiers to pull moisture from planks and subflooring, often saving the floor.
Hardwood Floor Water Damage RestorationMusty odors mean moisture is still present or mold has started. We find the source with moisture meters and thermal cameras, dry it, then treat with antimicrobial solution. Odor disappears when the moisture does.
Water Damage Odor RemovalNorth Texas storms bring wind-driven rain, roof leaks, and flash flooding. We handle emergency extraction, drying, and repairs after storm damage. Keller's storm season keeps our crews busy from spring through fall.
Storm Water Damage RestorationBurst pipes are the most common winter call we get in Keller. We shut off the water, extract, dry the structure, and coordinate the pipe repair. Freeze events can split multiple lines in one home.
Burst Pipe Water Damage RepairWashing machine hoses, water heater tanks, and refrigerator lines fail without warning. We extract the water, dry the surrounding floors and walls, and check for moisture under cabinets and behind appliances.
Appliance Leak CleanupRoof leaks show up as ceiling stains, but the water travels. We trace it with infrared cameras, dry the attic and ceiling structure, and repair the damaged drywall. Fixing the roof itself is coordinated with a roofing partner.
Roof Leak Water Damage RepairWe use moisture meters, thermal imaging cameras, infrared cameras, and boroscopes to find water you cannot see. Mapping tells us exactly where to place drying equipment so nothing gets missed. This step is included in every drying job.
Moisture Mapping & Leak DetectionIf you smell something musty after a leak, mold may already be growing. We inspect with moisture meters and thermal cameras, take samples when needed, and give you a clear report. Testing confirms whether remediation is necessary.
Mold Inspection & TestingFurniture, documents, and electronics can often be saved with specialized drying. We inventory affected items, dry what is salvageable, and document losses for your insurance claim. Items that cannot be saved are listed clearly.
Water Damage Content RestorationCommercial losses need fast drying to minimize business interruption. We handle large-scale extraction and drying for offices, retail, and warehouses in Keller and Tarrant County. Crews scale to the size of the job.
Commercial Water Damage RestorationWe document moisture readings, photograph damage, and prepare Xactimate-compatible reports your adjuster can process. That paperwork speeds up approvals and reduces disputes. We work directly with most major carriers.
Insurance Claim AssistanceWater damage does not wait for business hours. We answer calls 24 hours a day, seven days a week, including holidays. Keller-area response times typically run 60 to 90 minutes.
24/7 Emergency Water Damage ResponseCrawl space flooding causes wood rot and mold that spreads into the living space. We pump standing water, dry the joists and subflooring, and treat with antimicrobial solution. We also check for the source so it does not happen again.
Crawl Space Water RemovalDehumidifiers pull moisture from the air so wet materials can release their water. We use desiccant and refrigerant units sized to the job. In Keller's humid summers, dehumidification is often the difference between a four-day and a seven-day dry.
Dehumidification ServicesWhen drying is not enough, we repair the structure. That includes framing, subflooring, drywall, and finishes. We handle the repair scope after drying so your home is returned to pre-loss condition.
Structural Water Damage RepairReal experiences from customers who chose our Water Damage Drying services
A supply line to our fridge let go while we were at work. Pro Water Damage Restoration had a crew at the house in about an hour. They extracted the water, set air movers and a dehumidifier, and checked readings every day. Four days later the kitchen floor was dry and the baseboards were saved. The insurance report they gave us was thorough.
Homeowner, Keller
Our water heater burst in the garage and water ran into the hallway. I called at 11 p.m. and they answered. The tech used a thermal camera to find water under the tile that I never would have known about. Drying took five days, and they handled the claim paperwork with our adjuster. No mold, no smell.
Homeowner, Southlake
We had a slab leak in one of our rental units that soaked two bedrooms. Pro Water Damage Restoration handled the extraction and drying, and their daily moisture logs made the insurance process painless. They also coordinated the drywall repair afterward. I have used them three times now and they are my first call.
Property Manager, Roanoke
A supply line to our fridge let go while we were at work. Pro Water Damage Restoration had a crew at the house in about an hour. They extracted the water, set air movers and a dehumidifier, and checked readings every day. Four days later the kitchen floor was dry and the baseboards were saved. The insurance report they gave us was thorough.
Homeowner, Keller
Our water heater burst in the garage and water ran into the hallway. I called at 11 p.m. and they answered. The tech used a thermal camera to find water under the tile that I never would have known about. Drying took five days, and they handled the claim paperwork with our adjuster. No mold, no smell.
Homeowner, Southlake
Our IICRC-certified crews are on call 24/7 and typically reach Keller homes within 60 to 90 minutes. We have been drying Tarrant County properties since 2005. Call now and we will start extraction before the damage spreads.